Subaru

Putting together our final prototype was a bit easier for this project compared to other front-mount intercooler (FMIC) kits our team has developed. As mentioned in previous segments, we used the crash beam and intercooler from our 2015 WRX kit. Now we've worked up some functional prototype piping for a final test fit.

First, let's take a quick look at each portion of the kit.

Intercooler and Crash Beam

The intercooler core is the key component in any intercooler kit. This core has provided significant air temperature drops during our testing on the WRX, and we expect the same results with the STi.

Mishimoto STi intercooler and crash beam

With our cold-side piping complete, it was time to focus on the hot side. This portion of the piping system would require a bit more attention, mainly because we were unable to scavenge any existing pipes from our WRX/STI front-mount intercooler kits (as we did with the cold side). Let's get to it!

Piping Fabrication

The hot-side piping will route from the turbocharger compressor outlet, around the driver side of the engine bay, and into the front bumper area to attach to the intercooler.

Here is a look at the turbocharger connection point.

2015 STi front-mount intercooler hot-side pipe turbo connection

A coupler attaches the pipe to the turbocharger.

Our first segment of this STI intercooler project involved the test fitting of our WRX crash beam and intercooler core. We were able to verify fitment of both pieces, which allowed our team to move on to piping fabrication. We are starting this kit with the cold-side pipe, which we've decided to place this on the passenger side of the engine bay to reduce the piping length as much as possible. Following this strategy should help reduce lag seen by the driver.

Pipe Fabrication

The cold-side pipe is a great place to start because we are able to use a portion of one of our existing kits. Because the 2015 model shares the EJ from the 2008+, we will be reusing the pipe that attaches to the throttle body and incorporates the BPV (bypass valve).

" width="300" height="180">

Interested in picking up our 2008-2014 WRX/STi overflow tank? Check out our discounted pre-sale linked below.

2008-2014 Subaru WRX aluminum overflow tank pre-sale!

We last left you with some details of our initial design and a hint of an upcoming pre-sale for this overflow tank. Unfortunately, since that initial test fit we hit a few snags in the design process. Our goal with this product is to provide compatible fitment with all our other 2008+ WRX and STi components. This required numerous stages of test fitting, one of which revealed an issue. With our larger 3-row X-Line aluminum radiator installed, our sight tube on this expansion tank design ended up too close to the belt drive system on our Subaru.

We decided a revision was necessary. Although the two components were not physically touching, the clearances were just too tight for our comfort. Luckily, our team had an

The progress on our intake system is coming along nicely for this Forester XT. We have created a pipe that will fit well with our airbox design and filter selection. Remember, our pipe is within the acceptable pipe diameter to run this system with a stock tune.

The Fabricated Prototype

Below are some shots of the system we plan to put on an FXT for testing. The routing for this tube will follow a more direct path from filter to turbo. This is especially helpful for when the car is sitting at idle with ambient air around the box. With a shorter pipe distance, it will take less time for fresher, cooler air to get to the engine upon acceleration over stock. Check out images of the initial design below!

Prototype Subaru Forester parts

We're back with another quick update on our TGV delete project for the 2015+ WRX. After designing our initial models and then 3D-printing a prototype for test fitting, we worked up a couple functional prototypes for on-car testing.

First Prototype Images

Check out a few images of our functional prototype deletes!

Mishimoto's 2015 WRX TGV delete prototypes

Mishimoto's 2015 WRX TGV delete

3D-Printed Prototypes

To confirm the dimensions and design of our prototype, we decided to utilize some of our rapid prototyping tools. We fired up our 3D printer and loaded the model. Check out a couple images showing the progress of the print.

3D-printing 2015 WRX parts

3D-printing 2015 WRX parts

Once the printing process was complete, we cleaned up the prototypes and installed them on our 2015 WRX to verify fitment.