Page 79 - Engineering

In our last post we took a good look at the stock Fiesta ST exhaust and the initial design of our cat-back exhaust. The exhaust was fabricated and installed on the car and then it was time to test the stock system.

To Resonate or Not to Resonate

Getting the sound just right was quite a process. Our initial prototype featured 2.5" piping with a single rear muffler. This design did not feature a resonated mid-pipe unlike the stock unit. The initial design was sound tested on the dyno and also test driven by several members of the team. While we loved the low growl of the exhaust as it was, we wanted to test a resonated version before settling on a final design. As with all exhaust development projects, we are aiming for a final product that sounds great on throttle while still being

Interested in picking up our NB Miata oil cooler kit? Check out our discounted pre-sale linked below.

Mishimoto 1999-2005 Mazda Miata Oil Cooler Kit Pre-Sale!

In our last segment, we outlined the goals of the project, and we started fabricating mounting brackets to position our heat exchanger under the front of the Miata NB (second generation). We also hinted at the use of shrouding to direct airflow properly through our cooler.

Optimal airflow through a heat exchanger is vital to the efficiency derived from an oil cooler system. In addition, we see value in retaining the stock engine undertray, which aids in the proper regulation of coolant temperatures. We will build our air duct into the undertray, with the goal of a stock-like appearance on the top of our list, right next to optimal airflow.

Air Duct Fabrication

First, we needed to create some space to fit our ducting. We ordered

Interested in purchasing our awesome intake system? Check out our product page linked below!

Mishimoto Nissan 350Z Performance Air Intake!

Last time we dyno tested our assembled prototype for sound and performance. Maximum gains were achieved in the midrange of the rpm band to the tune of 10 whp and 13 wtq. These are impressive numbers. We saw gains from the start of the pull through redline, averaging around 5-7 whp/wtq throughout.

The sound produced by the VQ with our intake installed is nothing short of awesome! The large air filter and reduced restriction produces a deeper, amplified induction tone that sounds quite satisfying from behind the wheel.

Our last task is to fully model our design in Solidworks and construct our final prototype for fitment confirmation. As we mentioned last time, minor tweaks were needed to perfect fitment.

Intake 3D

With just a couple small tasks to go, we're near the completion of this 2015 Mustang cat-back exhaust project. Our design for this system is complete from the downpipe connection to the end of the stainless exhaust tips.

3D Models

Our prototype exhaust meets our requirements for both fitment and performance, so it was time to create a 3D-model of our design, which would ensure that our manufactured exhausts match our design exactly. After some time at the computer screen working in Solidworks, we ended up with the awesome renderings below!

Mishimoto 2015 Mustang EcoBoost exhaust rendering

Interested in picking up our 2008-2014 WRX/STi overflow tank? Check out our discounted pre-sale linked below.

2008-2014 Subaru WRX aluminum overflow tank pre-sale!

If you haven't noticed, the folks here at Mishimoto are not fans of plastic use for cooling system components. A large number of our products provide a more durable material, aluminum, to replace the failure-prone plastic parts, and now we are focusing on another line of products, our aluminum coolant expansion tanks. We offer two different options for the WRX/STI and one for the new Mustang EcoBoost. This article is focused around our newest addition, an aluminum overflow tank for the 2008+ WRX and STI.

Product Design

We won't be making any significant changes to the design of this tank compared to the stock unit, except for the construction material. Enlarging the tank's capacity will

Team Mishi likes to look out for our Subaru community. If you have been following our engineering blog, then you'll notice that we have been rolling out a slew of high quality 2015+ parts WRX. One of the biggest products we launched was our bolt-on intake system. Not only did we provide easy power gains, but our system greatly improved sound, and created a large group of very pleased customers. The gains we produced were a result of reduced restrictions compared to the factory system. A great product that supports stock and mildly modified examples. We are now turning our attention to an even less restrictive iteration that will be designed to support vehicles necessitating maximum airflow.

Our race-inspired design for this WRX intake will take the more aggressive route of obtaining the maximum power potential an intake can deliver to this FA series motor. Keep in mind, this secondary "Race" design will require tuning for safe operation.

It is important to understand that this

If you follow our Ford Powerstroke 6.0L product line, you are aware of the high- and low-temperature thermostats we released last year. The high-temperature unit quickly became a customer favorite as a reliable way to improve engine operation, in-cabin heat, and fuel mileage. These benefits are particularly useful in the cold-weather months. Our low-temperature thermostat offers a lower recovery temperature compared to the factory unit, which can help keep coolant temperatures regulated during towing or when transporting heavy loads.

During the release of the thermostats, we had numerous requests for a replacement housing. The factory housing is a casted piece, which isn't aesthetically pleasing, but it is easy to replace.

Product Development

Development began in a pretty simple fashion. We acquired an OEM housing and started capturing measurements so that we could reverse-engineer the piece.

Dyno preparation for Fiesta ST parts testing

Testing day has finally arrived and it's time to see how our new Fiesta ST parts perform! After weeks of prototype design and fabrication, we have our first prototype Ford Fiesta ST intake system ready for dyno testing. Our first round of product testing is being conducted for two reasons:

First, we want to evaluate power output. Our initial post explained that we were skeptical about making power with our intake. The Fiesta is a MAP-based vehicle and only uses its MAF sensor to gather temperature data. Through our years of development, extracting additional power from speed density (MAP-calculated) is a bit of a challenge. The gains we usually see on these vehicles is a result of reduced restriction within the intake tract. With this intake we've certainly improved flow, so let's see what we are able to produce.

Our second goal

Introduction and the Stock Downpipe

Another addition to the Fiesta ST collection! Our Fiesta build is coming along nicely, and I am happy to announce some progress on our downpipe project. As with any R&D undertaking the first step is to take a look at the stock setup and see how it can be improved.

Stock Fiesta ST downpipe

Although Ford has a pretty nice design, we are planning to make it a bit better by increasing the diameter of the downpipe to 3" throughout. As opposed to the stock unit which features 3" pipe only where the downpipe meets the turbo. In order to achieve excellent fitment with the turbo, we will keep the flange as similar to stock as possible. To collect the most accurate measurements

Interested in picking up our NB Miata oil cooler kit? Check out our discounted pre-sale linked below.

Mishimoto 1999-2005 Mazda Miata Oil Cooler Kit Pre-Sale!

The Mazda Miata MX-5 is the most-raced production vehicle in the world. It's a great top-down cruiser, features low entry-level pricing, and it's inexpensive to modify and repair. Fuel mileage is fantastic. Saying the Miata is the end-all and be-all vehicle would be a stretch (it has its limitations), but it is one hell of a car and an amazing bang-for-your buck regardless of use. If you do not understand any of this, I urge you to go out and drive one of these cars. If you've already driven one and still don't get it, perhaps you need to try again.

In all seriousness, the Miata is a fantastic car that deserves attention from the aftermarket. We offer a variety of cooling components for the NA/NB models, including several aluminum radiator options, electric